Water remaining on the base of the dishwasher at the end of the washing or no drainage of the water is one of the most common faults. Often the problem is not a complex electronic failure, but a clogged filter or a twisted drain hose. In this article, we’ll take a step-by-step look at why water isn’t going away and explain solutions you can make yourself at home. Filter and drain zone at the base of the dishwasher
1.

Check Base Filter
The filter, located on the bottom of the dishwasher under the rotating lower spray arm, protects the pump by retaining food residues. Over time, oil, lime and food residue clog this filter. Remove the filter by turning it counterclockwise, brushing thoroughly with an old toothbrush under hot water. The fine residues remaining in the metal strainer section are usually the main responsible for the slow flow of water.

Remember to fit the filter tightly after cleaning it; a loose filter will cause glass and fork debris to escape into the pump. 2. Inspect the Drain Hose
The drain hose to the sink drain or siphon from the back of the machine may be kinked, crushed, or clogged with a layer of oil inside. Pull the machine slightly forward and make sure that the hose is not bent.

You can check the blockage by removing the hose and passing warm water through it. In addition, the flushing nozzle to which the hose is connected is also frequently clogged; disassembling and cleaning this point often completely solves the problem. Dishwasher overview and rear drain connection
3. Check Drain Pump and Impeller
If the filter and hose are clean, it is the drain pump’s turn. You can see the impeller when you open the pump cover at the bottom of the filter.

A shard of glass, fruit kernel or toothpick can block the impeller, preventing the pump from running. After unplugging the machine, gently rotate the propeller by hand; if it does not rotate freely, clean the foreign object trapped between it. If the pump does not make any noise, the motor may have malfunctioned and needs to be replaced. 4. Maintenance Tips to Accelerate Water Drainage
Regular maintenance greatly prevents evacuation problems.

Before putting the plates in the machine, throw away the coarse residues, run vinegar or machine cleaner on an empty schedule once a month and check the filter at least every two weeks. Monitoring the anti-limescale salt level in hard water zones protects both the pump and the heater. These simple habits extend the life of your machine. When to Apply to the Service?

If you have checked the filter, hose and pump but the water is still not draining, the problem may be with the drain pump motor or the electronic board. If there is a buzz from the pump and the water does not go away, the motor winding may have malfunctioned. In such electrical failures, it is best to contact a qualified technician for your own safety. Practical Habits to Prevent Evacuation Problems
Most evacuation failures are actually caused by preventable causes.

The most important habit is to scrap the coarse leftovers before placing the dishes in the machine. Rice grains, tea leaves, crusts and small pieces of bone go directly to the filter and pump. In addition, always operating the machine with products made for the dishwasher prevents excessive foam and residue formation.

Sert su bölgelerinde yaşıyorsanız, kireç önleyici tuz haznesini düzenli kontrol etmek hem tahliye yollarını hem de ısıtıcıyı korur. Bu küçük alışkanlıklar, makinenizin yıllarca sorunsuz tahliye yapmasını sağlar. Tahliye Yaparken Çıkan Sesler Ne Anlama Gelir? Tahliye sırasında duyduğunuz sesler, arızanın türü hakkında ipucu verir. Normalde pompa düzenli ve yumuşak bir uğultu çıkarır.

Eğer keskin bir vızıltı duyup su gitmiyorsa, pompa çalışmaya çalışıyor ama pervane bir cisim tarafından bloke edilmiş olabilir. Tıkırtı veya takırtı sesleri, pervaneye sıkışmış cam ya da plastik parçaya işaret eder. Hiç ses gelmiyorsa pompaya elektrik gitmiyor ya da motoru yanmış olabilir. Bu sesleri dinleyerek, servisi aramadan önce sorunun kaynağını büyük ölçüde daraltabilirsiniz.

Güvenliğiniz için her müdahaleden önce makinenin fişini mutlaka çekin.